Configuring The Adsl Interface Ujniper 2 Configuring the Device The NetScreen device allows any type of traffic to the Internet that originates from neyscreen in your Trust zone, but does not allow any traffic that originates in the Internet to reach your network. Connecting The Power NetScreen recommends using a surge protector for the power connection.
Configuring The Wireless Network By default, the wireless1 interface is bound to the Wzone1 zone and does not have an IP address assigned to it. Got it, continue to print. Indicates the port has not established a link with another device. Operational mode change will erase current configuration and reset the device, continue?
Although you can use this shortcut when entering commands, all the commands documented here are presented in their entirety. Chapter 2 Configuring the Device The NetScreen device allows any type of traffic to the Internet that originates nwtscreen devices in your Trust zone, but does not allow any traffic that originates in the Internet to reach your network.
Page 13 You can run power cords and Ethernet cables through the openings in the floor of the tray or junier the depressions in the back wall. Required Configuration Using a Console Connection The Console port on the NetScreen-5GT Wireless device allows you to access the device through 5gg serial cable connected to your workstation or terminal. This manual also for: Contents Changing the Trust Interface Address Page 29 Operational mode change will erase current configuration and reset the device, continue?
Table of Contents Add to my manuals Add. Changing The Admin Manuual And Password Chapter 2 Configuring the Device Changing the Admin Name and Password Because all NetScreen products use the same default admin name and password netscreenit is highly advisable to change your admin name and password immediately. By default, the wireless1 interface is bound to the Wzone1 zone and does not have mannual IP address assigned to it.
To configure the device using a console connection, enter ScreenOS CLI commands on your terminal or in a terminal emulation program on your workstation.
These nestcreen settings are such that, in most cases, there are only a few items that you must configure. The NetScreen-5GT Wireless rack-mount kit includes installation instructions and a rack-mounting tray. Chapter 2 Configuring the Device Changing the Admin Name and Password Because all NetScreen products use the same default admin name and password netscreenit is highly advisable to change your admin name and password immediately.
Therefore, change the port mode before configuring the device. Enter text from picture: You must first connect the device to a modem, using an RS port, and then connect the modem to the line. Netscreen Publications Although you can use this shortcut when entering commands, all the commands documented here are presented in their entirety. Chapter 1 Connecting the Device This chapter describes how to connect the NetScreen-5GT Wireless device to the network, connect the power, and connect an antenna.
Configuring The Wireless Network By default, the wireless1 interface is bound to the Wzone1 zone and does not have an IP address assigned to it. This manual has three chapters and one appendix. Page of 40 Go. To employ a standard UART port, both the console and the modem maual use this configuration.
You can run power cords and Ethernet cables through the openings in the floor of the tray or out the depressions in the back wall. Preface This manual has three chapters and one appendix. Click Objects in the menu column. You must first connect nehscreen device to a modem, using an RS port, and then connect the modem to the line. Operational mode change will erase current configuration and reset the device, continue? Enter text from picture: Changing The Admin Name And Password Chapter 2 Configuring the Device Changing the Admin Name and Password Because all NetScreen products use the same default admin name and password netscreenit is highly advisable to change your admin name and password immediately.
Required Configuration Using a Console Connection The Console port on the NetScreen-5GT Wireless device allows you to access the device through a serial cable connected to your workstation or terminal. By default, the wireless1 interface is bound to the Wzone1 zone and does not have an IP address assigned to it. Page 13 You can run power cords and Ethernet cables through the openings in the floor of the tray or out the depressions in the back wall. Chapter 2 Configuring the Device Changing the Admin Name and Password Because all NetScreen products use the same default admin name and password netscreenit is highly advisable to change your admin name and password immediately.
Indicates the port is connected to a 10 Base-T device. These default settings are such that, in most cases, there netsxreen only a few items that you must configure. You can also use the space behind the devices to hold power supplies.
If you are using the optional NetScreen-5GT Wireless rack mount kit, then use the rack mounting instructions that are included at the end of this chapter. Chapter 2 Configuring the Device The NetScreen device allows any type of traffic to the Internet that originates from devices in your Trust manuao, but does not allow any traffic that originates in the Internet to reach your network. Page 29 Operational mode change will erase netscresn configuration and reset the device, continue?
To configure the device using a console connection, enter ScreenOS CLI commands on your terminal or in a terminal emulation program on your workstation. Connecting The Power NetScreen recommends using a surge protector for the power connection.
0コメント